OPC UA PubSub Traps And Pitfalls

Error "Unable to activate the adapter (...). Return code: -5"

We have observed this error with Npcap 0.996. Upgrading to Npcap 0.9987 has resolved the problem.

Error "Unable to activate the adapter (...). Return code: -8"

On Linux, elevated privileges are needed in order to send raw Ethernet packets. Run your program with sudo to resolve this issue. On Windows, depending on how the driver was installed, elevated privileges might be needed as well.

Error "Unable to load shared library 'libpcap' or one of its dependencies. ..."

If you are on Ubuntu 18: Libpcap is "preinstalled", but SharpPcap won't find it. There are various ways how to resolve it. One of them is to create a copy of symlink /usr/lib/x86_64-linux-gnu/libpcap.so.0.8 to symlink libpcap.so in the same directory. On various other systems (tested with Ubuntu 20): "sudo apt-get install libpcap-dev".

My subscription filter matches the publisher configuration, but messages are still being filtered out.

Make sure that you only put information to the filter that is actually contained in the messages. For example, you may have specified a concrete dataset writer ID, based on the publisher configuration, in your filter. But, in UADP fixed profile, the dataset writer ID is not actually transmitted in the network messages, and therefore you must use zero for the dataset writer ID in your filter.

Subscriber does not receive anything, even when no filter is specified - but I am sure the publisher works.

With UDP or Ethernet protocols, check that you are publishing and subscribing on the intended network interfaces. On computers with multiple interfaces, which are common nowadays, a default interface is chosen by the software when no interface is specified, and it may commonly be a wrong choice. In tools like OpcCmd or UADemoSubscriber, use the --ConnectionNetworkInterface (-cni) option. In subscriber code, set the InterfaceName property of UAPubSubConnectionDescriptor.ResourceAddress. With MQTT protocol, check that the broker queue name (which is interpreted as topic name filter) is correct. When the topic name filter is incorrect, MQTT gives no error, but you will most likely receive no messages. In tools like OpcCmd or UADemoSubscriber, the broker queue name is specified using the --BrokerQueueName (-bqn) option.

Subscriber does not receive anything, when on the same host as the publisher.

This happens with some network adapters. You can install and use a loopback adapter to make it work. On Windows 10, run Add Hardware Wizard (hdwwiz.exe), tell it that you want to select the hardware manually from a list, and from Network Adapters, select Microsoft -> Microsoft KM-TEST Loopback Adapter. Be careful - adding a new adapter without further configuration may have other, sometimes unforeseen, consequences - such as that traffic might get routed into the adapter when you do not want it. It is recommended that you disable the adapter when not in use for your tests.

There is a delay after the connection is established, before the dataset messages start coming.

This may be due to use of delta frames by the publisher. QuickOPC does not deliver incomplete datasets (from the delta frames) to you. It therefore needs to wait for the first key frame.

When publishing with UDP unicast, no messages appear in network analyzer.

Make sure the destination host is actually reachable on the network. For destination hosts on the local network, the destination IP address needs to be resolvable using ARP before a unicast packet can be even sent out. For destination hosts on other networks, it must be possible to resolve its IP address via the routing table.

How to obtain network interface names

On Windows

On Windows, we recommend using the following command to obtain a list of available network interfaces:
  netsh interface ip show interfaces

Other related Windows commands are:

netsh interface show interface
ipconfig |findstr "adapter"
netsh mbn show interfaces
wmic nic get NetConnectionID

On Linux

On Linux, we recommend using the following command to obtain a list of available network interfaces:
  netstat -i

Other related Linux commands are:

ip link show
nmcli device status
nmcli connection show
ifconfig -a

In command-line utilities

In the OpcCmd utility and UADemoPublisher, you can use the following command to show information that describes all network interfaces on the local computer:
  system networkInformation listInterfaces